Brand new radio (RF) replacement remote control BENINCA TO.GO2VA.
It is intended for these models BENINCA: BILL4024M, BULL.5M, BULL424ESA, BULL5M, BULL624TURBO, HEADY, JIM4, JM.3, KBIL40M.P, KBOB21M, KBULL8M.P, KIT, KMS.5P, KPONY.P, MB24/MBE24. (There may not be listed all compatible models. If you are not sure, just tell us your device model (by online chat, email), we will promptly check, verify if compatible with your device. The verified compatibility is guaranteed by us.)
Technical details:- Frequency: 433,92 MHz (+- 100kHz)
- Code type: ROLLING CODE (64bit) / ARC128bit
- Battery: 12V, type 23A
- Dimensions: 65 x 39 x14 mm
- Operating temperature range: -20 °C to+55 °C
- Transmitted power: on average 1 mW E.R.P.
- Transmitter range: up to 100 m (outdoors with antenna), 35 m (indoors)
- Battery life: an average of 2 years, with 10 work cycles per day
SELECTION OF CODING TYPE (TO.GO/HAPPY VA)
The VA series remote controls (TO.GO VA and HAPPY VA) can operate in HCS mode (Benincà Rolling-code) or ARC mode (Advanced Rolling-code). This allows the transmitters to be used on systems equipped with HCS receivers. The transmitter is factory set to ARC mode.
To change the code type:
- Press and hold buttons T1 and T2 simultaneously.
- After about 3 seconds, the LED will start to blink, the number of blinks indicates the currently set code:
- 3 blinks + pause 1s = ARC mode
- 4 blinks + pause 1s = ARC + HCS mode*
- 2 blinks + pause 1s = HCS mode
- If the buttons are held down for an additional (approximately 20s), the LED will light up continuously for 3 seconds. Releasing the buttons during these 3 seconds will switch the transmitter to the next mode (3 >> 4 >> 2 >> 3 >> 4 >> ...).
If buttons T1/T2 are released when the LED is not lit continuously, there will be no change in configuration.
*In this mode, the keys on the left (1 and 3) are coded ARC and the keys on the right (2 and 4) are HCS.
It is a brand new RF (radio) remote control for gates or garage door with roling code. You HAVE TO REGISTER the new remote control into the original main unit. The pairing method is very simple.




















Remote control radio(RF) for BENINCA TO.GO2VA same design and functions









Brand new radio (RF) replacement remote control BENINCA TO.GO2VA.
It is intended for these models BENINCA: BILL4024M, BULL.5M, BULL424ESA, BULL5M, BULL624TURBO, HEADY, JIM4, JM.3, KBIL40M.P, KBOB21M, KBULL8M.P, KIT, KMS.5P, KPONY.P, MB24/MBE24. (There may not be listed all compatible models. If you are not sure, just tell us your device model (by online chat, email), we will promptly check, verify if compatible with your device. The verified compatibility is guaranteed by us.)
Technical details:- Frequency: 433,92 MHz (+- 100kHz)
- Code type: ROLLING CODE (64bit) / ARC128bit
- Battery: 12V, type 23A
- Dimensions: 65 x 39 x14 mm
- Operating temperature range: -20 °C to+55 °C
- Transmitted power: on average 1 mW E.R.P.
- Transmitter range: up to 100 m (outdoors with antenna), 35 m (indoors)
- Battery life: an average of 2 years, with 10 work cycles per day
SELECTION OF CODING TYPE (TO.GO/HAPPY VA)
The VA series remote controls (TO.GO VA and HAPPY VA) can operate in HCS mode (Benincà Rolling-code) or ARC mode (Advanced Rolling-code). This allows the transmitters to be used on systems equipped with HCS receivers. The transmitter is factory set to ARC mode.
To change the code type:
- Press and hold buttons T1 and T2 simultaneously.
- After about 3 seconds, the LED will start to blink, the number of blinks indicates the currently set code:
- 3 blinks + pause 1s = ARC mode
- 4 blinks + pause 1s = ARC + HCS mode*
- 2 blinks + pause 1s = HCS mode
- If the buttons are held down for an additional (approximately 20s), the LED will light up continuously for 3 seconds. Releasing the buttons during these 3 seconds will switch the transmitter to the next mode (3 >> 4 >> 2 >> 3 >> 4 >> ...).
If buttons T1/T2 are released when the LED is not lit continuously, there will be no change in configuration.
*In this mode, the keys on the left (1 and 3) are coded ARC and the keys on the right (2 and 4) are HCS.
It is a brand new RF (radio) remote control for gates or garage door with roling code. You HAVE TO REGISTER the new remote control into the original main unit. The pairing method is very simple.






















Featured Products
General BAR silver - simple remote control
General ZOOMY Remote control with big buttons for seniors, kids

Share your device's brand and model, and we'll handle the rest. Our experts will handle the request and your tailored recommendations will be on their way via email.