12402

SOMMER SLIDER 4020 TX03-868-4 - radio (RF) remote control, replacement

15628.jpg
15629.jpg12894.jpg64.jpg
Price BRUTTO:
(VAT 21%)
19.0 EUR
Part number:SLIDER-4020-gate
Availability:> 10 pieces in stock
Warranty terms: Brand new, 2 years guarantee,
accepting returns within 30 days
 
Pcs

Delivery to EU: 2 to 7 days, non-EU: 2-20 days

SHIPPING COST WORLDWIDE IS 7.1 EUR

Replacement remote control SOMMER SLIDER 4020 TX03-868-4 (SLIDER 4020 TX038684) - 100% replacement 1:1 of the original remote control.

The remote control supplied is already pre-programmed on buttons 1 and 2. You only need to register the remote control to your original receiving unit memory!

Remote control is dedicated for SOMMER device models: APERTO, DUO, DUO VISION, RUNNER, SPRINT, TWIST. (There may not be listed all compatible models. If you are not sure, just tell us your device model (by online chat, email), we will promptly check, verify if compatible. The verified compatibility is quaranteed by us.)

This remote control is available on branded remote control General GATE (shown on the left). We guarantee that the remote control will perform all the functions of the original RC.

  • The RF remote control General GATE fully replaces the original remote control.
  • Only one single remote control could be used up for 4 different brands or models of different Frequencies (270-870 MHz).
  • Remote control works with both fixed and rolling codes.
  • Multifrequency auto-scan remote control.
  • Copying/cloning of the code/protocol from the original remote control.
  • Battery Panasonic CR2032 included.
  • Dimensions: 69 x 34 x 10 mm
  • If any specific colour required, state this information to the customers’ note during placing an order.

How to copy the code from the original remote control:

  1. While holding button no. 1 pushed, press four times button no. 4 on the remote control General GATE.
  2. Release both buttons. LED diode flashes shortly approx. every 2 sec.
  3. Put the original remote control (2-3 centimetres) in the front of General GATE.
  4. Push and hold button you would like to copy on the original remote control until LED diode flashes quickly (before quick flashing the diode shines permanently).
  5. While LED diode flashes quickly, push and hold required button on General GATE until LED diode goes off as a confirmation of successful copying of the code.
  6. Copy was successfully made. Now it is important to log the new remote control into the original receiving unit.

How to REGISTER the new remote control into the original receiving unit:

  1. Remove the translucent cover from the control unit.
  2. Press the button labeled CODE, the LED indicator will light up and indicate learning mode start.
  3. By repeatedly pressing the CODE button, you can switch between channels (can be 1-4) to which remote control you want to register.
  4. Within 10 seconds, press and hold the selected button on the remote control to write to the controller.
  5. The LED will start flashing to indicate that the transmit code has been memorized and will turn off. Writing the remote control to the memory of the control unit is complete, you can test the remote control.

One single RF General GATE remote control for all: gate, garage door, venetian blind and indoor lightning. Other 3 buttons of the remote control could be programmed for other devices which require RF (radio) remote control. So it can control up to 4 different devices / receivers. This remote control could be used and programmed for any brand (with both fixed and rolling code). General GATE is THE ONLY RF remote control that you can program with codes of different door/gate manufacturers/frequencies into one General GATE. Supported frequency 280-870 MHz.



For SOMMER


 

.
Copyright © 2021 REMOTE CONTROL WORLD.