Moveto ARM300/400 - replacement remote control General GATE

Price BRUTTO:
(VAT 21%)
18.9 EUR
Price NETTO 15.6 EUR
Part number:Moveto-ARM300/400-generalGATE
In Stock:10 pieces
Warranty terms: Warranty 2 years + 100% satisfaction or your money back in two weeks limit
 
Pcs

The goods will be shipped within 24 hours after your order. The delivery time to EU is from 3 to 7 days.
Price includes the fee for disposal of electronic waste.

SHIPPING COST WORLDWIDE IS 5.1 EUR

Replacement remote control MOVETO ARM300/400. This replacement has all functions as the original remote control.

We supply replacement remote control General GATE (shown on the left side).

For models: ARM300, ARM300P, ARM400, ARM SOLAR and SLIDE 350, ARM 300, ARM 300 P, ARM 400


 

The RF remote control General GATE fully replaces the original remote control MOVETO.

Only one single remote control could be used up for 4 different brands or models of different frequencies.

Remote control works with both fixed and rolling codes.

Multifrequency auto-scan remote control.

Copying/cloning of the code/protocol from the original remote control.

Battery Panasonic CR2032 included.

Dimensions 69 x 39 x 10 mm

If any specific colour required, state this information to the customers’ note during placing an order.

The price is for 1 piece of the replacement remote control General GATE.


 

How to copy the code from the original remote control:

  1. While holding button no. 1 pushed, press four times button no. 2 on the remote control General GATE.

  2. Release both buttons. LED diode flashes shortly approx. every 2 sec.

  3. Put the original remote control (2-3 centimetres) in the front of General GATE.

  4. Push and hold button you would like to copy on the original remote control. LED diode will flash quickly as a confirmation of successful copying of the code.

  5. While LED diode flashes quickly, push required button on General GATE. LED diode will light up and then it will switch off.

  6. Copy was successfully made. Now it is important to log the new remote control into the original receiving unit.

 

How to log the new remote control into the original receiving unit:

  1. Remove the cover of the receiving unit.

  2. Find “RF” button.

  3. Push this button and hold it for 5 sec. Red diode should turn on.

  4. Push programmed button on General GATE. Red diode starts to flash.

  5. Push programmed button on General GATE once again for confirmation.


 

One single RF General GATE remote control for all: gate, garage door, venetian blind and indoor lightning. Other 3 buttons of the remote control could be programmed for other devices which require RF remote control. This remote control could be used and programmed for any brand (with both fixed and rolling code). General GATE is THE ONLY RF remote control which is suitable for more RF devices.



This product was added to our catalog on Wednesday 27 September, 2017.

Remote Control, Remote controls, Control remoto, mando a distancia, comandament a distància, mane a distància, Kauko-ohjain, Daljinski upravljač, Control remot, Fjernkontroll, Controle Remoto, Diaľkový ovládač, Даљински управљач, удаленный, Uzaktan Kumanda, 遠程控制, Fjernbetjening, Daljinskom upravljaču, Télécommande, Fernbedienung, Fernbedienungen, Távirányító, Pilot, Piloty, Afstandsbediening, Telecomando, telecomandi, távirányító , Távirányítók, controle remoto, telecomando, télécommande, Télécommandes, daljinskih upravlja?a, daljinski upravljalnik, Daljinski upravljalniki, distancinis valdymas, Nuotolinio valdymo pulteliai, Distancinio valdymo pultai, kaukosäädin, Kaukosäätimet, Piloty zdalnego sterowania, Zdalne sterowanie, fjärrkontroll , Fjärrkontroller, fjernbetjening, Fjernbetjeninger

 

.
Copyright © 2017 REMOTE CONTROL WORLD.