10376

FAAC XT2, XT4 868MHz replacement remote control General GATE

FAAC XT2, XT4 868MHz replacement remote control General GATE FAAC XT2, XT4 868MHz replacement remote control General GATE
Price BRUTTO:
(VAT 21%)
17.9 EUR
Part number:FAAC-D600-generalGATE
Availability:> 10 pieces in stock
Warranty terms: Brand new, 2 years guarantee,
accepting returns within 30 days
Manufactured by: FAAC
 
Pcs

Delivery to EU: 2 to 7 days, non-EU: 2-20 days

SHIPPING COST WORLDWIDE IS 6.6 EUR

Battery






Replacement remote control compatible with remote control FAAC XT2, XT4. Functionality of the remote control is the same as the original. The remote control supplied is already pre-programmed on buttons 1 and 2. You only need to register the remote control to your original receiving unit memory.

For models: D600DELPHIN, D600DOLPHIN, D600, D700HS, D1000, FAAC 415, FAAC 390, FAAC 391, FAAC 400, FAAC 402, FAAC 412, FAAC 413, FAAC 422

The replacement remote control General GATE shown on the left side!

  • The RF remote control General GATE fully replaces the original remote control.
  • Only one single remote control could be used up for 4 different brands or models of different frequencies.
  • Remote control works with both fixed and rolling codes.
  • Multifrequency auto-scan remote control.
  • Copying/cloning of the code/protocol from the original remote control.
  • Battery Panasonic CR2032 included.
  • Dimensions 69 x 39 x 10 mm
  • If any specific colour required, state this information to the customers’ note during placing an order.
  • The price is for 1 piece of the replacement remote control General GATE.

RF remote control General GATE.

How to copy the code from the original remote control:

  1. While holding button no. 1 pushed, press four times button no. 4 on the remote control General GATE.
  2. Release both buttons. LED diode flashes shortly approx. every 2 sec.
  3. Put the original remote control (2-3 centimetres) in the front of General GATE. (see the picture above)
  4. Push and hold button you would like to copy on the original remote control. LED diode will flash for a moment.
  5. Release this button on the original remote control and then immediately press P1 and P2 (on the original remote control) until the diode flashes permanently.
  6. Push and hold same button (as in point 4.) you would like to copy on the original remote control. LED diode will flash quickly as a confirmation of successful copying of the code.
  7. Once LED diode on the General GATE remote flashes fast, by pressing chosen button on General GATE you upload copied code from your original remote control. LED will flash once.
  8. Continue with second button programming.

How to REGISTER the new remote control into the original receiving unit:

  1. Press both P1 and P4 buttons on the General GATE simultaneously
  2. LED is flashing fast, release both buttons
  3. On the receiving unit press OPEN A button, the diode will start flashing
  4. The diode in the receiving unit flashes for approx.. 5 seconds – during this time you are able to register the new remote control. Press programmed button on the General GATE. LED diode in the RU will flash for few seconds, then it goes off. Registration was successful.
  5. New remote control General GATE could be used now.

One single RF General GATE remote control for all: gate, garage door, venetian blind and indoor lightning. Other 3 buttons of the remote control could be programmed for other devices which require RF remote control. This remote control could be used and programmed for any brand (with both fixed and rolling code). General GATE is THE ONLY RF remote control which is suitable for more RF devices.



This product was added to our catalog on Saturday 27 June, 2020.

For FAAC


 

.
Copyright © 2020 REMOTE CONTROL WORLD.