12366

BFT MITTO B - radio (RF) remote control, replacement

15572.jpg
15573.jpg12894.jpg64.jpg
Price BRUTTO:
(VAT 21%)
19.0 EUR
Part number:MITTO B-gate
Availability:> 10 pieces in stock
Warranty terms: Brand new, 2 years guarantee,
accepting returns within 30 days
 
Pcs

Delivery to EU: 2 to 7 days, non-EU: 2-20 days

SHIPPING COST WORLDWIDE IS 7.1 EUR

Replacement remote control BFT MITTO B - 100% replacement of the original remote control.

The remote control supplied is already pre-programmed on buttons 1 and 2. You only need to register the remote control to your original receiving unit memory!

Remote control is dedicated for BFT device models: MITTO B, MITTO RCB02, MITTO RCB04. (There may not be listed all compatible models. If you are not sure, just tell us your device model (by online chat, email), we will promptly check, verify if compatible. The verified compatibility is quaranteed by us.)

This remote control is available on branded remote control General GATE (seen on the left side). We guarantee that the remote control will perform all the functions of the original RC.

  • The RF remote control General GATE fully replaces the original remote control.
  • Only one single remote control could be used up for 4 different brands or models of different Frequencies (270-870 MHz).
  • Remote control works with both fixed and rolling codes.
  • Multifrequency auto-scan remote control.
  • Copying/cloning of the code/protocol from the original remote control.
  • Battery Panasonic CR2032 included.
  • Dimensions: 69 x 34 x 10 mm
  • If any specific colour required, state this information to the customers’ note during placing an order.

How to copy the code from the original remote control:

  1. While holding button no. 1 pushed, press four times button no. 4 on the remote control General GATE.
  2. Release both buttons. LED diode flashes shortly approx. every 2 sec.
  3. Put the original remote control (2-3 centimetres) in the front of General GATE.
  4. Push and hold button you would like to copy on the original remote control until LED diode shines permanently.
  5. The LED diode on General GATE shines permanently (approx. every 2 sec.). This informs you that you need to transmit SEED code for successful duplication.
  6. Now prepare the original remote control for transmitting SEED code. Push and hold buttons 1 and 2 on the original remote control until the LED diode shines permanently (older types have hidden button next to the battery case which has same function as simultaneous pressing of buttons 1 and 2).
  7. While LED diode on the original remote control shines permanently, place it in front of the General GATE remote control (2-5 centimetres). Push and hold button you would like to copy on the original remote control until LED diode on General GATE flashes faster than before – this confirms successful duplication of the code. This step might take few seconds.
  8. Now push and hold required button on General GATE until the LED diode goes off as a confirmation of successful saving of the code.

How to REGISTER the new remote control into the original receiving unit:

  1. Press once button SW1, LED starts flashing.
  2. Press both P1 and P4 buttons on the General GATE simultaneously until the diode flashes fast.
  3. Press button 1 (saved function on the General GATE), LED diode will be flashing fast which means it was saved into the memory successfully.
  4. Wait until LED goes off.

One single RF General GATE remote control for all: gate, garage door, venetian blind and indoor lightning. Other 3 buttons of the remote control could be programmed for other devices which require RF (radio) remote control. So it can control up to 4 different devices / receivers. This remote control could be used and programmed for any brand (with both fixed and rolling code). General GATE is THE ONLY RF remote control that you can program with codes of different door/gate manufacturers/frequencies into one General GATE. Supported frequency 280-870 MHz.



For BFT


 

.
Copyright © 2021 REMOTE CONTROL WORLD.