Replacement radio (RF) remote control fully compatible with type AVIDSEN 504250.

A perfect 1:1 copy designed and manufactured by our company – has all functions of the original remote for these AVIDSEN models: ASTRELL 120, ASTRELL 200, ASTRELL 300, ASTRELL 400, ASTRELL 50, ASTRELL 85, AVIDSEN 150, AVIDSEN 350, AVIDSEN 60, AVIDSEN AXE 4230, AVIDSEN EVER212, AVIDSEN EVER300, AVIDSEN ROD120, AVIDSEN SLIDE200, AVIDSEN SLIDE400, AVIDSEN TEC400, AVIDSEN TEC500, AVIDSEN XC420, AVIDSEN XP300+, EVER 212, EVER 85, KHEA, OPEN BOX, SLIDE 200, SLIDE 400, SLIDE 800, TEC 400, TEC 500 (There may not be listed all compatible models. If you are not sure, just tell us your device model (by online chat, email), we will promptly check, verify if compatible with your device. The verified compatibility is guaranteed by us.)

This remote control is available on branded remote control General VATRONIC (shown on the left). We guarantee that the remote control will perform all the functions of the original RC.

• The RF remote control General VATRONIC fully replaces the original remote control.
• Only one single remote control could be used up for 4 different brands or models of different Frequencies (270-870 MHz).
• Remote control works with both fixed and rolling codes.
• Multi-frequency auto-scan remote control.
• Copying/cloning transmitting code/protocol from the original remote.
• Includes a 3V CR2032 battery and a metal keychain carabiner.
• Dimensions: 73 x 31 x 11 mm
• If any specific colour required, state this information to the customers note when placing an order.

The remote control supplied is already pre-programmed on buttons 1 and 2. You only need to register the remote control to your original receiving unit memory.

Procedure for copying the code from the original remote control:

1. Press and hold the button X on General VATRONIC and then press the button ✓ 4 times.
2. Release both buttons. The red indicator LED on the General VATRONIC remote will briefly flash every two seconds.
3. Place the original remote control that you want to duplicate in front of or next to the General VATRONIC control.
4. On the original remote control, press and hold the button that you want to duplicate. Keep it pressed on the original until the red LED on the General VATRONIC control lights up. Then release the button on the original remote control.
5. After a short moment, the red indicator LED on the General VATRONIC control will flash twice every two seconds. This alert informs the user that to successfully complete the duplication, a signal still needs to be sent.
6. Press the same button on the original remote control as in step 4 and hold it.
7. The LED on the General VATRONIC remote will change its blinking speed (it will blink faster) and the color of the indicator LED will change to blue, confirming successful learning of the code.
8. At this moment, press the button on the General VATRONIC control where you want to save the code. The blue LED on the remote will briefly light up and turn off. This will confirm successful saving of the code to the selected button.
9. The copy has been successfully created. The General VATRONIC remote needs to be registered with the drive unit (see the manual for the drive/receiver).

How to REGISTER the new remote control into the original main unit:

1. Remove the Control Unit cover.
2. Press the button labeled "RF2" on the electronic board, LED1 will light up. LED1 will turn off after 5 seconds.
3. Press the button on the remote control you want to register, LED2 indicator will light up.
4. Now the remote control is registered in the Control Unit memory. Test its functionality.

One RF General VATRONIC remote for everything: You can clone controls for another gate/garage door, blinds, remotely controlled sockets, and anything else you have at home with RF (radio) remote control on the other 3 buttons in a similar way. Thus, it can control up to 4 different devices/receivers. Receivers can be of different (any) brands and frequencies with both fixed and floating codes. General VATRONIC and General GATE are indeed the ONLY RF remote controls on the market that are truly so universal that you can program codes from various gate and door manufacturers into one remote. Supported frequency 280-870 MHz.