Replacement radio (RF) remote control fully compatible with the type BFT TRC2.
The remote control has been specially developed for the following BFT models: ADEST, ARES ULTRA BT, BOTTICELLLI, CLONIC, DEIMOS AC, DEIMOS BT, EOS 120, PHIBOS BTA40, TELEC MA, TOUIANO. (There may not be listed all compatible models. If you are not sure, just tell us your device model (by online chat, email), we will promptly check, verify if compatible with your device. The verified compatibility is guaranteed by us.)
This remote control is available on branded remote control General GATE (shown on the left). We guarantee that the remote control will perform all the functions of the original RC.
- The RF remote control General GATE fully replaces the original remote control.
- Only one single remote control could be used up for 4 different brands or models of different Frequencies (270-870 MHz).
- Remote control works with both fixed and rolling codes.
- Multifrequency auto-scan remote control.
- Copying/cloning of the code/protocol from the original remote control.
- Battery Panasonic CR2032 included.
- Dimensions: 69 x 34 x 10 mm
- If any specific colour required, state this information to the customers’ note during placing an order.
The remote control supplied is already pre-programmed on buttons 1 and 2. You only need to register the remote control to your original receiving unit memory
Copying Code from the Original Remote Control:
- Press and hold button 1 on the General GATE remote control, and then press button 2 four times.
- Release both buttons. The blue indicator LED on the General GATE remote control will briefly flash every two seconds.
- Place the original remote control that you want to duplicate in front of or next to the General GATE remote control.
- On the original remote control, press and hold the button you want to duplicate. Keep holding the button on the original remote control until the blue LED on the General GATE remote control lights up. Then release the button on the original remote.
- After a short while, the blue indicator LED on the General GATE will blink twice (every two seconds). This alert informs the user that sending the source "SEED" code is necessary for successful duplication.
- Simultaneously press buttons 1 and 2 on the original remote control to transmit the SEED code. There will be a brief delay before the LED on the original remote lights up (NOTE: THESE BUTTONS ARE PLACED DIAGONALLY).
- While the LED on the original remote control is blinking, place it back next to the General GATE remote control. Press the same button on the original remote control as in step 4 and hold it down until the LED on the General GATE remote control changes its blinking rate (it will blink faster) and the indicator LED turns red.
- At this point, press the button where you want to save the code. The red LED on the remote control will briefly light up and then turn off, confirming the correct code storage on the selected button.
How to REGISTER the new remote control into the original main unit:
- Remove the cover of the BFT drive unit
- First the JUMPER - marked J1 - must be connected.
- Press and hold buttons 1 and 2 on the GENERAL GATE before it flashes rapidly. Then release the buttons - the GATE is ready to send the hidden button/function.
- Now simultaneously press buttons SW1 and SW2 briefly (for one second). The green LED will start flashing.
- While the GENERAL GATE is blinking rapidly press the selected button for that gate. The green LED will light up permanently.
- When the GENERAL GATE goes out, press the same button on the GENERAL GATE again. The green LED will flash again. The button has been added to the memory of the BFT unit.
- Wait 60 seconds for the programming to turn itself off.
- You can unzip the JUMPER.
One single RF General GATE remote control for all: gate, garage door, venetian blind and indoor lightning. Other 3 buttons of the remote control could be programmed for other devices which require RF (radio) remote control. So it can control up to 4 different devices / receivers. This remote control could be used and programmed for any brand (with both fixed and rolling code). General GATE is THE ONLY RF remote control that you can program with codes of different door/gate manufacturers/frequencies into one General GATE. Supported frequency 280-870 MHz.
Featured Products
General BAR silver - simple remote control
General ZOOMY Remote control with big buttons for seniors, kids
Share your device's brand and model, and we'll handle the rest. Our experts will handle the request and your tailored recommendations will be on their way via email.