Replacement radio (RF) remote control fully compatible with type BENINCA IO.2WV.

Perfect 1:1 copy designed and manufactured by our company – has all the functions of the original remote for these models of brand BENINCA: RR.2WIV. (There may not be listed all compatible models. If you are not sure, just tell us your device model (by online chat, email), we will promptly check, verify if compatible with your device. The verified compatibility is guaranteed by us.)

This remote control is available on branded remote control General VATRONIC (shown on the left). We guarantee that the remote control will perform all the functions of the original RC.

• The RF remote control General VATRONIC fully replaces the original remote control.
• Only one single remote control could be used up for 4 different brands or models of different Frequencies (270-870 MHz).
• Remote control works with both fixed and rolling codes.
• Multi-frequency auto-scan remote control.
• Copying/cloning transmitting code/protocol from the original remote.
• Includes a 3V CR2032 battery and a metal keychain carabiner.
• Dimensions: 73 x 31 x 11 mm
• If any specific colour required, state this information to the customers note when placing an order.

The remote control supplied is already pre-programmed on buttons ▲ and ▼. You only need to register the remote control to your original receiving unit memory.

Procedure for copying the code from the original remote control:

1. Press and hold the button X on General VATRONIC and then press the button ✓ 4 times.
2. Release both buttons. The red indicator LED on the General VATRONIC remote will briefly flash every two seconds.
3. Place the original remote control that you want to duplicate in front of or next to the General VATRONIC remote.
4. On the original remote control, press and hold the button that you want to duplicate. Keep it pressed until the blue indicator LED on the General VATRONIC remote starts flashing rapidly.
5. At this moment, press the button on the General VATRONIC remote where you want to save the code. The blue LED on the remote will briefly light up and turn off - this confirms the code has been saved.
6. The copy has been successfully created. The General VATRONIC remote needs to be registered with the drive unit (see the manual for the drive/receiver).

How to REGISTER the new remote control into the original main unit:

Procedure for registering the remote control to the control unit without a DISPLAY:

1. Remove the unit cover.
2. On the circuit board, find the programming button (PGM). Press this button for >2 seconds - the LED will light up and remain lit.
3. Within 10 seconds, briefly press the button for about >3 seconds on the registered remote control.
4. The unit will blink as a confirmation of receiving the remote control into memory.
5. Wait about 30 seconds and test the remote control.

Procedure for registering the DO to the control unit with a DISPLAY:

Next to the display, there are 3 buttons/microswitches + / OK / -

1. Press the OK button briefly (max. 2 seconds), the display will light up and various messages will appear
2. Using the + or - buttons, select the command on the display RADIO / rAdi / rAd (one of these three versions will be displayed)
3. Confirm the program by briefly pressing the OK button
4. The display will show the message PP, confirm the function again by briefly pressing OK
5. Now the display will guide you - PUSH = press and hold the button that you need to register into the memory of the control unit
6. Once the display shows OK, the remote control has been successfully registered *
7. Now simultaneously press the + and - buttons to exit programming
8. Repeat the procedure of step 7 until the display turns off

One RF General VATRONIC remote for everything: You can clone controls for another gate/garage door, blinds, remotely controlled sockets, and anything else you have at home with RF (radio) remote control on the other 3 buttons in a similar way. Thus, it can control up to 4 different devices/receivers. Receivers can be of different (any) brands and frequencies with both fixed and floating codes. General VATRONIC and General GATE are indeed the ONLY RF remote controls on the market that are truly so universal that you can program codes from various gate and door manufacturers into one remote. Supported frequency 280-870 MHz.