6791

DUCATI transmiter 4 - radio (RF) remote control, replacement

44.jpg
Price BRUTTO:
(VAT 21%)
18.7 EUR
Part number:transmiter-40-gate
Availability:> 10 pieces in stock
Warranty terms: Brand new, 2 years guarantee,
accepting returns within 30 days
Manufactured by: DUCATI
 
Pcs

Delivery to EU: 2 to 7 days, non-EU: 2-20 days

SHIPPING COST WORLDWIDE IS 6.9 EUR

Battery






Replacement remote control DUCATI transmiter 4 - 100% replacement of the original remote control.

Attention please: there is another 2nd model - NOT compatible (only with RF RECEIVER)! Choose remote control according to your former one appearance.

The remote control supplied is already pre-programmed on buttons 1 and 2. You only need to register the remote control to your original receiving unit memory!

Remote control is dedicated for DUCATI device models: ARM 300, ARM 300 P, ARM 400, ARM SOLAR A SLIDE 350, ARM300, ARM300P, ARM400, OTIO 771014, OTIO 771015, OTIO 771016. (There may not be listed all compatible models. If you are not sure, just tell us your device model (by online chat, email), we will promptly check, verify if compatible. The verified compatibility is quaranteed by us.)

This remote control is available on branded remote control General GATE (seen on the left side). We guarantee that the remote control will perform all the functions of the original RC.

  • The RF remote control General GATE fully replaces the original remote control.
  • Only one single remote control could be used up for 4 different brands or models of different Frequencies (270-870 MHz).
  • Remote control works with both fixed and rolling codes.
  • Multifrequency auto-scan remote control.
  • Copying/cloning of the code/protocol from the original remote control.
  • Battery Panasonic CR2032 included.
  • Dimensions: 69 x 34 x 10 mm
  • If any specific colour required, state this information to the customers’ note during placing an order.

How to copy the code from the original remote control:

  1. While holding button no. 1 pushed, press four times button no. 4 on the remote control General GATE.
  2. Release both buttons. LED diode flashes shortly approx. every 2 sec.
  3. Put the original remote control (2-3 centimetres) in the front of General GATE.
  4. Push and hold button you would like to copy on the original remote control until LED diode shines permanently. Then you can release the button.
  5. The LED diode on General GATE flashes twice approx. every 2 sec. This informs you that you need to transmit signal to finish this duplication successfully.
  6. Now push and hold the same button as in the point no. 4.
  7. LED diode on General GATE flashes faster than before – this confirms successful duplication of the code. This step might take few seconds.
  8. Now push and hold required button on General GATE until the LED diode goes off as a confirmation of successful duplication.

How to REGISTER the new remote control into the original receiving unit:

  1. Remove the cover of the receiving unit.
  2. Find “RF” button.
  3. Push this button and hold it for 5 sec. Red diode should turn on.
  4. Push programmed button on General GATE. Red diode starts to flash.
  5. Push programmed button on General GATE once again for confirmation.

One single RF General GATE remote control for all: gate, garage door, venetian blind and indoor lightning. Other 3 buttons of the remote control could be programmed for other devices which require RF (radio) remote control. So it can control up to 4 different devices / receivers. This remote control could be used and programmed for any brand (with both fixed and rolling code). General GATE is THE ONLY RF remote control that you can program with codes of different door/gate manufacturers/frequencies into one General GATE. Supported frequency 280-870 MHz.



For DUCATI


 

.
Copyright © 2021 REMOTE CONTROL WORLD.